User’s Guide - Paradox Security

4m ago
54 Views
0 Downloads
350.70 KB
20 Pages
Last View : 3m ago
Last Download : n/a
Upload by : Kaydence Vann
Transcription

32-Zone Wireless Transceiver Control PanelMG5000MG32LEDMG10LEDHMG32LRFMG10LEDVUser’s Guide

Access CodesHow do I program Access Codes?1.Press the [2.3.The [ ] key will flash. When a zone LED or zone key is lit (not flashing), the user is already programmed.Select a user by entering a 2-digit user number (i.e. [0] [9] for user 9) or use the scroll keys and then press [ENTER]. For the MG10LEDV/H, press the keycorresponding to the user number (i.e. [9] for user 9).Enter a new 4- or 6-digit [ACCESS CODE].Confirm the code.Press a button on the designated remote or press [ENTER] to skip if there is no remote to program.(Partitioned system only) Press [1] and/or [2] to assign the user to a partition. Press [ENTER], the menu will now jump to the next available user.4.5.6.7.] key. Enter your [SYSTEM MASTER CODE] or either [MASTER CODE].For security reasons, write only the user’s name and not his or her access code. 4-Digit Codes NUser # and Name001: Master002: Master1Partition 1 or 21&216-Digit Codes NBypStayForceArm OnlyPGM OnlyDuress NNNDuress: Y N N N003: Master22004:N005:NNNNNDuress: Y N N N006:NNNNNDuress: Y N N N007:NNNNNDuress: Y N N N008:NNNNNDuress: Y N N N009:NNNNNDuress: Y N N N010:NNNNNDuress: Y N N N011:NNNNNDuress: Y N N N012:NNNNNDuress: Y N N N013:NNNNNDuress: Y N N N014:NNNNNDuress: Y N N N015:NNNNNDuress: Y N N N016:NNNNNDuress: Y N N N017:NNNNNDuress: Y N N N018:NNNNNDuress: Y N N N019:NNNNNDuress: Y N N N020:NNNNNDuress: Y N N N021:NNNNNDuress: Y N N N022:NNNNNDuress: Y N N N023:NNNNNDuress: Y N N N024:NNNNNDuress: Y N N N025:NNNNNDuress: Y N N N026:NNNNNDuress: Y N N N027:NNNNNDuress: Y N N N028:NNNNNDuress: Y N N N029:NNNNNDuress: Y N N N030:NNNNNDuress: Y N N N031:NNNNNDuress: Y N N N032:NNNNNDuress: Y N N NN

Table of ContentsPGM Keys (Programmable Outputs) . 10Power Save Mode . 11Trouble Display . 11Access Codes. 0Trouble List . 11Overview. 2Basic Operations . 2Auditory Feedback.Visual Feedback .Overview of the Magellan Series Keypads .Partitioning.2223Access Codes . 4Programming Access Codes. 4System Master Code (Default: 123456) .Master Codes .Duress Code.Programming Access Codes .4444Advanced Features .12Quick Function Keys. 12Test Report .Call PC.Answer PC .Cancel Communication.12121212Testing & Maintenance . 12System Checklist. 13Stay Arming. 5Zone Description.Special Keys and Features .Panic Alarms.PGMs .PGM Utility Keys .System Timers .Other Information .Delays .Communicator.System Options.One-Touch Arming . 6Master Quick Menu MG5000. 18Arming & Disarming . 5Regular Arming. 5Sleep Arming. 5One-Touch Regular Arming.One-Touch Stay Arming .One-Touch Sleep Arming .One-Touch Bypass Programming .Fast Exit.66666Auto-Arming. 7Timed Auto Arming . 7No Movement Auto Arming. 7Disarming & Deactivating an Alarm. 7Manual Bypass Programming. 7Bypass Recall Feature . 8System Features . 9Display Mode. 9Alarm Display. 9Fire Alarms . 9Minimizing Fire Hazards . 9Fire Safety Tips . 9Providing a Fire Warning System . 9Panic Alarms . 9Programming Chime Zones. 10Keypad Muting . 10Keypad Backlight. 1013141415151515171717Overview . 18User . 18

OverviewThank you for selecting the Magellan Security System from Paradox Security Systems Ltd. This advanced technology security systemprovides you with reliable security protection and powerful features that anyone can use without memorizing complex and confusingcodes. The system consists of the Magellan control panel, one or more Magellan keypad modules, various input devices (i.e. motiondetectors, door contacts, etc.) and various output devices (i.e. bells, sirens, lights, etc.).The elegant and user-friendly Magellan MG10LEDV/H, MG32LED, and MG32LRF keypad modules allow you to easily access yoursecurity system's functions and provide you with an easy-to-understand display of your security system's alarm and operational status.All of the actions performed in your security system will be executed and displayed through the keypad. Therefore, before using yoursecurity system, we highly recommend that you read this manual carefully and have your installer explain basic system operation to you.Basic OperationsAuditory FeedbackWhen you enter information on the keypad, it will guide you with beep tones that communicate acceptance or rejection of yourentries. You should be familiar with these two keypad beep tones:Confirmation Beep: When an operation (i.e. arming/disarming) is successfully entered on the keypad or when the system switchesto a new status/mode, the keypad produces an intermittent beep tone (“BEEP-BEEP-BEEP-BEEP”).Rejection Beep: When the system reverts to its previous status or when an operation is incorrectly entered on the keypad, it will emita continuous beep tone (“BEEEEEEEEP”).Visual FeedbackKeypad Indicator Lights: All Magellan keypads include coloured lights which convey the current status of your system. The state ofeach light represents a specific condition in your system.Many of the features in your system must be enabled by the installer. If the feature is not programmed, the keypad will emit arejection beep and the action will be cancelled. Refer to System Checklist on page 12 and 13 for details.Overview of the Magellan Series KeypadsThe numbers and keys of the Magellan series keypad’s screen communicate your system’s status.Figure 1: MG10LEDV (10-zone LED Keypad Module)Off Light (red):On DisarmedOff System armedFast Flash Disarmed system inalarm (e.g. 24hr. zone)AC LightOn Power onOff Power off Press once [MASTERCODE] for Quick MenuProgramming)[TBL] Trouble displayPartition 1 StatusPartition 2 StatusFuture useArm (red), Sleep (yel), Stay (grn):On Partition armedOff Partition disarmedFlash Exit DelayFast Flash* Exit Delay (final 10 sec.)Fast Flash* Partition in alarm* Audible Indicators:Continuous beep AlarmVariable beep Fire alarmIntermittent beep Beginning of exit delayFast beep Final 10 sec. of exit delayON Trouble(s) occurring[MEM] Alarm memory displayON Alarm(s) occurred[BYP] Bypass programmingZone Display:The keypad [1] to [0(10)] correspond tozones 1 to 10 respectively.Open or entry delay zones are illuminated,and flash in alarm.ON Zone(s) bypassed2User Guide

Figure 1: MG32LED (32-zone LED Keypad Module)Zone Display:The numbers [1] to [32] correspond to zones 1 to 32 respectively.Open or entry delay zones are illuminated, and flash in alarm.Partition 1 StatusPartition 2 StatusArm (red), Sleep (yel), Stay (grn):On Partition armedOff Partition disarmedFlash Exit DelayFast Flash* Exit Delay (final 10 sec.)Fast Flash* Partition in alarmOff Light (red):On DisarmedOff System armedFast Flash Disarmed system in alarm(e.g. 24hr. zone)* Audible Indicators:Continuous beep AlarmVariable beep Fire alarmIntermittent beep Beginning of exit delayFast beep Final 10 sec. of exit delayAC LightOn Power onOff Power off[TBL] Trouble displayON Trouble(s) occurring[MEM] Alarm memory displayFUTURE USEON Alarm(s) occurred Press once [MASTERCODE] for Quick MenuProgramming[BYP] Bypass programmingON Zone(s) bypassedFigure 3: MG32LRF (32-zone Wireless LED Keypad Module)Zone Display:The numbers [1] to [32] correspond to zones 1 to 32 respectively.Open or entry delay zones are illuminated, and flash in alarm.Partition 1 StatusOff Light (red):ON DisarmedOFF System armedFast Flash Disarmed system in alarm(e.g. 24hr. zone)Power and RX/TX LightON Power onOFF Power offFLASH Communication failurewith panel/keypad notlearnedFASTFLASH Transmission/reception inprogressPartition 2 StatusArm (red), Sleep (yel), Stay (grn):On Partition armedOff Partition disarmedFlash Exit DelayFast Flash* Exit Delay (final 10 sec.)Fast Flash* Partition in alarm* Audible Indicators:Continuous beep Alarm,Variable beep Fire alarmIntermittent beep Beginning of exit delayFast beep Final 10 sec. of exit delaylnfo KeyRefresh display to see all open zones (seeRefresh Display on page 8)[TBL] Trouble displayFUTURE USE Press once [MASTERCODE] for Quick MenuProgrammingON Trouble(s) occurring[MEM] Alarm memory displayON Alarm(s) occurred[BYP] Bypass programmingON Zone(s) bypassedPartitioningYour Magellan system is equipped with a partitioning feature that can divide your alarm system into two distinct areas identified asPartition 1 and Partition 2. Partitioning can be used in installations where shared security systems are more practical, such as ahome office or warehouse building. When partitioned, each zone, each user code and many of your system's features can beassigned to either Partition 1, Partition 2, or both partitions.If the system is not partitioned, all zones, user codes, and features will be recognized as belonging to Partition 1.Magellan3

More Result...

Access CodesProgramming Access CodesAccess codes are personal identification numbers that allow you to enter certain programming modes, arm or disarm your system as wellas activate or deactivate PGMs. The Magellan security system supports the following: 1 System Master Code 2 Master Codes 29 User Access CodesFor information on how each access code can arm or disarm the system refer to the System Checklist on page 12 and 13.System Master Code (Default: 123456)The System Master Code can arm or disarm any partition using any of the methods described in this section and can create, modifyor delete any user access code (see Programming Access Codes below).Master CodesMaster Code 1 is permanently assigned to Partition 1 and can be used to create, modify or delete user access codes (seeProgramming Access Codes below) that are assigned to Partition 1.Master Code 2 is permanently assigned to Partition 2 (except when partitioning is disabled, Master Code 2 will be assigned toPartition 1) and can be used to create, modify or delete user access codes that are assigned to the same partition.Master Codes cannot modify or delete user access codes assigned to both partitions. Only the System Master Code can modify or deleteuser access codes assigned to both partitions.Duress CodeIf you are forced to arm or disarm your system, entering the access code with the duress option enabled will arm or disarm thesystem and immediately transmit a silent alert (Duress Code) to the monitoring station.Must be enabled by your installer.Programming Access CodesYour system can use either 4- or 6-digit access codes (see page 14), where each digit can be any value from 0 to 9. Six-digit codesare considered more difficult to “crack” and therefore, more secure. Avoid programming simple or obvious access codes, such asyour telephone number, address or codes such as 1234. Also, see the Master Quick Menu at the end of the manual (page 17).How do I program Access Codes?1.Press the [ ] key.2.Enter your [SYSTEM MASTER CODE] or either [MASTER CODE].3.The [ ] key will flash. When a zone LED or zone key is lit (not flashing), the user is already programmed.4.Select a user by entering a 2-digit user number (i.e. [0] [9] for user 9) or use the scroll keys and then press [ENTER]. For theMG10LEDV/H, press the key corresponding to the user number (i.e. [9] for user 9).5.Enter a new 4- or 6-digit [ACCESS CODE].6.Confirm the code.7.Press a button on the designated remote or press [ENTER] to skip if there is no remote to program.8.(Not available for non-partitioned system) Press [1] and/or [2] to assign the user to a partition. Press [ENTER], the menu willnow jump to the next available user, if you choose to continue.How do I delete Access Codes?41.Press the [ ] key.2.Enter your [SYSTEM MASTER CODE] or either [MASTER CODE].3.Select a user by entering a 2-digit user number (i.e. [0] [9] for user 9). For the MG10LEDV/H, enter a 1-digit user number (i.e.[9] for user 9).4.Press the [SLEEP] key until you hear the confirmation beep.User Guide

Arming & DisarmingTake full advantage of your Magellan system by familiarizing yourself with all the arming methods. If your system is not partitioned (seePartitioning on page 2), everything is considered as belonging to Partition 1.If you cannot arm because a zone is open, the system will enter in Bypass Programming. Enter the two digit zone to bypass and press [ENTER], orpress [ENTER] to bypass all open zones.Regular ArmingThis method will arm all the zones in the selected partition. Please note that Regular arming can also be activated using Auto-Arming (seepage 6) or One-Touch arming (see page 5).How do I Regular arm?1.Close all zones in the desired partition.2.Press [ARM] [ACCESS CODE].3.If you have access to both partitions (see Partitioning on page 2): Press the key corresponding to the desired partition ([1] or [2]). Forboth partitions, press the other key after the confirmation beep.Sleep ArmingSimilar to Stay arming, Sleep arming allows users to remain in a protected area, but provides a slightly higher level of protection. Forexample, in a two-story house, the perimeter is protected with Stay arming. With Sleep arming, the perimeter as well as the main floor isprotected (motion detectors, etc.), allowing you to roam the second floor and sleeping quarters. Sleep zones are zones that are bypassedwhen Sleep arming. For example, when you go to sleep at night, the entire premises except your bedroom is fully armed. Sleep armingcan also be activated using Auto-Arming (see page 6) or One-Touch arming (see page 5).How do I Sleep arm?1.Close all zones in the desired partition (except Sleep zones).2.Press the [SLEEP] key.3.Enter your [ACCESS CODE].4.If you have access to both partitions (see Partitioning on page 2): Press the key corresponding to the desired partition, [1] or [2].For both partitions, press the other key after the confirmation beep.Stay ArmingThis method allows you to roam freely within the premises while the perimeter is fully armed. Stay zones are zones that are bypassedwhen Stay arming. For example, if you plan on staying in for the night, doors and windows can be armed without arming other zones likemotion detectors. Stay arming can also be activated using Auto-Arming (see page 6) or One-Touch arming (see page 5).How do I Stay arm?1.Close all zones in the desired partition (except Stay zones).2.Press the [STAY] key.3.Enter your [ACCESS CODE].4.If you have access to both partitions (see Partitioning on page 2): Press the key corresponding to the desired partition, [1] or [2].For both partitions, press the other key after the confirmation beep.Magellan5

One-Touch ArmingOne-Touch arming allows you to arm the system without using an access code. This feature must be enabled by your installer.If One-Touch Arming is programmed, you can increase the security level of your system (from Disarmwithout a code. See Figure 4 on page 5.Stay ArmSleep ArmFull Arm)One-Touch Regular ArmingPress and hold the [ARM] key for 3 seconds to arm all zones in the partition. If partitioned, keys [1] & [2] will flash. You can use thisfeature to allow specific individuals like service personnel (i.e. cleaners) to arm without giving them access to any other alarmsystem operations. For details on Regular arming, refer to page 4.One-Touch Stay ArmingPress and hold the [STAY] key for 3 seconds to arm the perimeter (zones not defined as Stay zones). For details on Stay arming,refer to page 4.One-Touch Sleep ArmingPress and hold the [SLEEP] key for 3 seconds to arm all zones not defined as Sleep zones. For details on Sleep arming, refer to page4.One-Touch Bypass ProgrammingPress and hold the [BYP] key for 3 seconds to access Bypass Programming Mode. For details on Bypass Programming, refer topage 6.Fast ExitWhen the system is already Stay or Sleep armed: This feature will allow you to exit already armed premises and keep the systemarmed. Press and hold the [OFF] key for 3 seconds to start the exit delay. After the exit delay has elapsed, the system will switch toits previous arming mode.Figure 4: Arming/DisarmingARMTo Sleep Arm:[SLEEP] CodeNo CodeSLEEPTo Disarm:[OFF] CodeNo CodeTo Stay Arm:[STAY] CodeTo Disarm:[OFF] CodeNo CodeSTAYTo Disarm:[OFF] CodeNo CodeOFF6User Guide

Auto-ArmingThe Magellan alarm system can be programmed to automatically arm upon the following two conditions.Timed Auto ArmingThe alarm system can automatically arm itself at a specified time everyday. As with Regular arming (see page 4), the system willbypass any open zones. Your installer can enable this option, but you can program the time of day the system will automatically arm.How do I program the Auto-Arm Timer?1. Press the [] key.2. Enter [MASTER CODE].3. Press the [BYP] key. The [BYP] key will flash to indicate you are in the System Options menu.4. Press key [1] to set partition 1, or press key [2] to set partition 2.5. Enter the desired time for auto arm (24 hour clock, e.g. 18:30).6. Press key [1] to regular arm, key [2] to sleep arm, or key [3] to stay arm the partition.No Movement Auto ArmingThe alarm system can be programmed to arm the system and/or send a report if no zone activity occurs for a pre-programmedamount of time. This is a particularly useful feature when supervising an individual with chronic health problems or a person wholives alone. The system will bypass any open zones. This feature must be set by your installer.Disarming & Deactivating an AlarmTo disarm an armed system or an alarm, press [OFF] and enter your [ACCESS CODE]. An entry point, like the front door, will beprogrammed with one of two Entry Delay Timers. When an entry point is opened, the keypad will beep until you disarm the system.Your alarm system will not generate an alarm until this timer elapses. Any user can disarm a partition they have been assigned to,except users assigned with the Arm Only Option or PGM Only Option.To disarm alarms generated by a Delayed Fire Zone, pleaserefer to Fire Alarms on page 8.How do I disarm the system?For a Stay or Sleep armed system, go to step 2.1.Enter through a designated entry point (i.e. front door).2.Press [OFF] enter [ACCESS CODE].3.If you have access to both partitions (see Partitioning on page 2): Press the key corresponding to the desired partition ([1] or [2]).For both partitions, press the other key after the confirmation beep.How do I deactivate an alarm?Press [OFF] enter [ACCESS CODE].Manual Bypass ProgrammingManual Bypass Programming allows you to program the alarm system to ignore (deactivate) specified zones the next time thesystem is armed. For example, you may wish to bypass certain zones when workers are renovating part of your establishment. Oncethe system is disarmed, the bypass entries are erased. Manual Bypass Programming can also be activated by using One-TouchBypass Programming (see note below). To remove the Bypass feature from a zone, in step 3 enter the zone number again or press[CLEAR] to erase all current entries. When zones are bypassed, the [BYP] key will illuminate.How do I bypass zones?1.Press the [BYP] key.2.Enter your [ACCESS CODE] (see the note below). The [BYP] key will flash.3.Illuminate the number(s) corresponding to the zone(s) you want to bypass by entering the two-digit zone number (i.e. zone 3 03). Solid on Zone open, Flash Zone bypass, Off Zone closed, not bypassed.4.Press the [ENTER] key to save and exit.If One-Touch Bypass Programming is enabled, press the [BYP] key for three seconds to enter Bypass Programming.Press [ENTER] after step 2 to bypass all open zones. Press [CLEAR] twice to exit without saving. Press [CLEAR] [ENTER] to delete bypassedzones.Magellan7

Bypass Recall FeatureAfter disarming the system, the bypass entries are erased. The Bypass Recall feature reinstates the previous bypass entries savedin memory. This eliminates the need to manually re-program the bypass entries every time you arm the system.How do I recall bypass entries?1. Press the [BYP] key2. Enter your [ACCESS CODE]3. Press the [BYP] key.4. Press the [ENTER] key.8User Guide

System FeaturesDisplay Mode(MG32LRF only)The MG32LRF has two display modes. By default, the keypad will show all events (e.g. zones in alarm, bypassed zones, etc.) live asthey occur. Alternatively, the system can be programmed by your installer to only display zones that cause an alarm or entry delay. If youwant to see the status of all zones, press the [ ] key. Zones that are open but have not triggered an alarm will only be displayed afterpressing the [ ] key. The display will appear for 30 seconds, showing the status of all zones at the time the [ ] key was pressed. Thezone display will shut off after 30 seconds. For more information on the two display modes, contact your installer.Alarm DisplayIf an alarm has occurred on a zone, the respective zone LED will flash, the [MEM] key will light up, and the zones will be stored in memory.These respective LEDs will continue to flash until disarming even if the zones are restored. To exit this mode and switch to live displaymode before disarming, press the [CLEAR] key. Once the system is disarmed, the zones’ LEDs will turn off, while the [MEM] key remainslit. Press the [MEM] key to illuminate the LEDs corresponding to the zones that were in alarm. The alarm memory will be erased when thenext alarm occurs and after a valid code is entered.Fire AlarmsUpon a fire alarm, the bell/siren will emit three “squawks” at 2 second intervals until silenced or reset by entering a valid access code. Ifthe zone is a Delayed Fire Zone, there is a delay before the system contacts the monitoring station. This will prevent unnecessaryreporting of false alarms. If there is no fire condition, contact your monitoring station immediately to avoid an unnecessary response.What do I do if a delayed fire zone was set off accidentally?1. Press the [CLEAR] key within 30 seconds of the alarm.2. Try to correct the problem.3. If the problem persists, after 90 seconds, the alarm will sound again. Press the [CLEAR] key again.Minimizing Fire HazardsThe three most common causes of fires: Cooking is the leading cause of home fires in the U.S. It's also the leading cause of fire injuries. Cooking fires often result fromunattended cooking and human error, rather than mechanical failure of stoves or ovens. Careless smoking is the leading cause of fire deaths. Smoke detectors and smolder-resistant bedding and upholstered furnitureare significant fire deterrents. Heating is the second leading cause of residential fires. However, heating fires are a larger problem in single family homes than inapartments since the heating systems in single family homes are often not professionally maintained.Fire Safety Tips In the event of a fire, escape first, then call for help. Develop a home fire escape plan and designate a meeting place outside. Makesure everyone in the family knows two ways to escape from every room. Practice feeling your way out with your eyes closed. Neverstand up in a fire, always crawl low under the smoke and try to keep your mouth covered. Never return to a burning building for anyreason; it may cost you your life. Finally, having at least one working smoke alarm dramatically increases your chances of surviving a fire. And remember to practicea home escape plan frequently with your family.Providing a Fire Warning SystemHousehold fires are especially dangerous at night. Fires produce smoke and deadly gases that can overcome occupants while theysleep. To warn against fire, smoke detectors should be installed outside each separate sleeping area in the immediate vicinity of thebedrooms and on each additional story of the family living unit, including basements.Panic AlarmsIn case of an emergency, the Magellan system can provide three panic alarms that can immediately generate an alarm aftersimultaneously pressing and holding two specific keys for three seconds. Based on your needs, these panic alarms can generate audiblealarms (sirens or bells) or silent alarms and can communicate specific messages to your monitoring station. For instance, pressing [1]and [3] can mean “call the police” or anything you require. This feature must be set by your installer.Press and hold keys [1] and [3] for the police.Press and hold keys [4] and [6] for a medical alarm.Press and hold keys [7] and [9] for a fire alarm.Magellan9

Programming Chime Zones(MG32LED & MG10LEDV/H - Hardwired Keypad Modules only)A Chime Enabled zone will advise you every time it is opened by causing your keypad to beep.Each keypad must be Chimed separately.How do I chime zones? MG32LED (32-zone Hardwired LED Keypad Modules only)1. Press & hold the [T] key for 3 seconds. The Arm1, Arm2, Stay1, and Stay2 LEDs will flash.2. Select the numbers corresponding to the zones you want to Chime by entering the two-digit zone number. For example, to chimezone 2 enter [0] then [2]. The corresponding LED will light up. The keypad will automatically save once the 2-digit zone number isentered.3. Press the [ENTER] key to exit.To remove the Chime feature from a zone, in step 2 enter the zone number again so the number extinguishes or press [SLEEP] toremove Chiming from all zones programmed to Chime. Any zones that are already Chimed will also illuminate. Zones that remain off orextinguished are not Chimed.How do I chime zones? MG10LEDV/H (10-zone LED Keypad Modules only)1. Press & hold the zone key ([1] to [0(10)]) for 3 seconds. Accept beep Chime on, Fail beep Chime off.Keypad MutingWhen muted, the keypad will only emit the confirmation beep, rejection beep, and beep when a key is pressed. Therefore, when muted,the keypad will not beep during an alarm and will not beep for chime enabled zones.Press and hold the [CLEAR] key for 6 seconds to enable or disable Keypad Muting. If the keypad emits a confirmation beep, KeypadMuting is enabled for that keypad. If the keypad emits a rejection beep, the feature is disabled.Each keypad must be muted separately.Keypad BacklightThe illumination level behind the keys can be modified to suit your needs. There are four backlight levels. The [S] or [MEM] key is usedto set the desired level. Each consecutive push of the [S] or [MEM] key will increase the backlight level until the maximum level isreached. After reaching the maximum level, the backlight level will return to the lowest level and the whole process is repeated.How do I modify the backlight? MG32LED / MG32LRF (32-zone Hardwired & Wireless LED Keypad Modules only)1. Press and hold the [S] key for 3 seconds. The [MEM] key will illuminate.2. Press the [S] key to set the desired backlight level.3. Press [CLEAR] or [ENTER] to exit.How do I modify the backlight? MG10LEDV/H (10-zone LED Keypad Modules only1. Press and hold the [MEM] key for 3 seconds. The [MEM] key will illuminate.2. Press the [MEM] key to set the desired backlight level.3. Press [CLEAR] or [ENTER] to exit.PGM Keys (Programmable Outputs)Your Magellan system may include one or more programmable outputs (PGMs). When a specific event or con

Overview of the Magellan Series Keypads The numbers and keys of the Magellan series keypad’s screen communicate your system’s status. [TBL] Trouble display ON Trouble(s) occurring [MEM] Alarm memory display ON Alarm(s) occurred [BYP] Bypass programming ON Zone(s) bypas